Free UK Shipping
On Orders £30+. Next Day on Orders £80+
Same Day Dispatch
Weekday Orders Placed Before 3pm
Free Returns
100% Satisfaction Guaranteed
Lifetime Support
With Extended Warranties
Free UK Shipping
On Orders £30+. Next Day on Orders £80+
Same Day Dispatch
Weekday Orders Placed Before 3pm
Lifetime Support
With Extended Warranties
Home > CO2 Regulators > Single Stage With Solenoid > CO2 Regulator With Solenoid & Dual Gauges

CO2 Regulator With Solenoid & Dual Gauges

£68.99 Sorry, out of stock

System Customisation

 
 

Key Facts

  • High quality design and manufacture.
  • For use with CO2 cylinders with horizontal valve orientation or our range of 'Advanced' adapters.
  • Dual pressure gauges indicating cylinder pressure and output working pressure.
  • Solenoid magnetic valve allows for CO2 to be switch on/off at defined times.
  • Output pressure set to 3 bar, suitable for aquariums 80L - 500L.
  • Precision needle valve.
  • Industry standard nut, compatible with DIN 477 / BS 341 No. 8 / JIS m22-14 / W21.8-14 / .860" x 1/14 (covers UK, Europe and Asia).
  • Works with any CO2 diffuser.
  • Choice of plug and voltage.

Description

The regulator is designed to reduce the high pressure inside of a CO2 cylinder to a lower, usable pressure that can be utilised for aquaria.

During photosynthesis, plants use carbon dioxide and water, combined with light energy, to produce oxygen and sugars. However, during dark hours, plants stop photosynthesising and converting CO2 to O2, and therefore it is not advised to add CO2 to the aquarium as levels may rise to the point where is causes distress to your fish. The in-built solenoid magnetic valve enables you to configure the required times for CO2 release, for example, configuring it 'on' during the 'lights on' and 'off' during 'lights out' hours. This can be achieved with a mains timer plug or pH controller. You can also choose to upgrade to a 12v DC solenoid (mains transformer included), which provides safe, low temperature, and guaranteed no noise operation.

Instructions

  • Tighten nut to CO2 cylinder or adapter using appropriate sized wrench or spanner (do not attempt to hand-tighten).
  • Fully open the needle valve by turning anti-clockwise, and switch the solenoid on. This will reduce the initial pressure surge on the pressure gauges when the CO2 cylinder valve is opened.
  • Open flow of CO2 on the cylinder.
  • Turn solenoid off and close needle valve by turning fully anti-clockwise.
  • Connect your bubble counter or tubing to the regulator.
  • Turn solenoid on and begin flow of CO2 by turning the needle valve anti-clockwise.
  • Allow a couple of minutes for pressure to build in the tubing and diffuser.
  • Adjust needle valve until desired bubble rate is achieved.
  • Click here to read the full regulator setup guide
 

Customer Reviews

Average Rating

Individual Reviews

Aaron E. Verified Buyer 26th Jun 2020
Brilliant product. Far better than my previous Brilliant product. Far better than my previous
Michael J. Verified Buyer 18th Jun 2020
Brilliant, a must with co2 Brilliant, a must with co2
Vitaly L. Verified Buyer 24th May 2020
Perfect service and products. Absolutely will by again Perfect service and products. Absolutely will by again
Chrysanthos V. Verified Buyer 22nd May 2020
Not too much speech and blah blah. One word describes 100% the product. Excellent !! Not too much speech and blah blah. One word describes 100% the product. Excellent !!
Alisa T. Verified Buyer 12th May 2020
Does it's job. Generates heat during use, so you need to be careful. Does it's job. Generates heat during use, so you need to be careful.
Gary L. Verified Buyer 6th May 2020
Good product well happy with its performance Good product well happy with its performance
Mats H. Verified Buyer 24th Dec 2019
Good with a solenoid valve that can be connected to a timer Good with a solenoid valve that can be connected to a timer
Stephen S. Verified Buyer 15th Dec 2019
Nice quality regulator Nice quality regulator
Audrey M. Verified Buyer 3rd Dec 2019
I am very pleased with this unit after following the very good instructions for fitting we had no problems I am very pleased with this unit after following the very good instructions for fitting we had no problems
Robert I. Verified Buyer 22nd Nov 2019
Massive built, easy to set up, working well, I am really happy with it Massive built, easy to set up, working well, I am really happy with it
See more reviews  Loading
Dual gauge CO2 regulator attached to cylinder
click image to view full screen

Photo Gallery

Cart Activity

Someone added a product to their cart

View Product

Someone added a product to their cart

View Product